Difference between revisions of "IAtty Reloaded"
Imeothanasis (Talk | contribs) |
Imeothanasis (Talk | contribs) |
||
Line 74: | Line 74: | ||
If you want a little more air and you dont want to change pin, adjust the center pin by unscrewing it a little | If you want a little more air and you dont want to change pin, adjust the center pin by unscrewing it a little | ||
− | |||
− | [File:Main appuie fort index.46.jpg|thumbnail]] | + | |
+ | [File:file:Main appuie fort index.46.jpg|thumbnail]] |
Revision as of 06:16, 11 January 2020
A Greek guy on our Favebook page told us that he loves his Iatty. Its the most tasty and with the thickest vapor atomizer he has ever tried. He is not alone on this. All people think alike for Iatty that was made 9 years ago, thats why our team decided to produce it again but in a modern way.
ps..... Iatty Reloaded will be sold only via preorders. At 15 of July 2019. We will announce the preorders on our FB page, here: https://www.facebook.com/groups/GoldenGreekFreaks/
Preorders will stay open until the end of August. After that, we will start the bulk production and in about 3 months you may have it in your hands.
Features:
MTL vape with a pin at 1,5 mm hole that can be adjusted to less air via the air ring on the base and 1 more pin at 2mm for open MTL that can also be adjusted to less air via the air ring on base.
Also, one more pin for tight MTL vape (without air hole), that let air pass around it and NOT inside it like on the other 2 pins. This pin works like a pin with 1mm hole
Tight DTL with a pin at 3mm hole
liquid control by turning the body. At the first stopper the liquid is fully open. At the opposite stopper the body comes out of the base to check your resistance. In any other position, the liquid control is semi-opened or closed
Air control via AFC ring on the base with several holes. At the first stopper the air is fully open and you can also separate the AFC ring from the base. At the opposite stopper the air is fully closed. In any other position, the air is semi-opened
material: SS 316L
plastic material between posts: PEEK
22mm in diameter
40,5mm in length in short version with 2ml liquid capacity
49mm in length in long version with 4ml liquid capacity (by adding an extension without the need of emptying the tank). You can add additional extensions, depending on how liquid independent you want to be.
Top refilling as all GG devices via two very big refilling hole
TIPS AND TRICKS
Close the liquid control before refill
Put liquid to the o-rings to make them slip easy
If you want to clean gurgling or to change pins without tools, please unscrew the base from the deck by keeping the whole body on one hand and the base on the other hand
Turn right the air ring and it will stop to the fully opened position. Also at this point you can pull off the base
Turn right the liquid control and it stops to the fully open position
Turn left the air ring and it stops to the fully closed position
Turn left the liquid control and separate the tank from the deck to check the resistance
Turn left the whole body to semi-close or totally close the liquid control
The blind pin that doesnt have hole inside, leaves air pass around it and works like a 1mm pin for tight MTL
The very small pin is for DTL vaping with a 3mm hole
The metal part inside the spares's bag that looks like the ceramic is to replace ceramic with SS. If you want to remove ceramic and SS too its ok but you also have to remove the o-ring because it will be close to the resistance
Dont screw hard the refilling cap because its useless to do that, you may also damage the o-rings and finally you cant unscrew it easy
Put as many extensions as you like to increase liquid capacity
If you use thin wire (up to 0,5mm), turn it half turn around the bolts to avoid shorts from excess wire when you cut it with pliers
Put the wick inside the feeding holes but just a little. Dont push it deep at the bottom of the holes
Take off the o-ring on the deck if you want very good feeding at high volts
Τhe center post extension is polygonal at its end so you can use a toll that fits on it when you want to unscrew it
If you want a little more air and you dont want to change pin, adjust the center pin by unscrewing it a little
[File:file:Main appuie fort index.46.jpg|thumbnail]]