The VIR is a state of the art electronic module created by GG, this latest GG innovation has taken 3 years in design and production.
The reason for the size is part of the design, Imeo wanted to make something very small to reduce the overall size of the mod. As well as the size the main purpose of VIR is to offer a product that does more than provide a good vape, it offers a much safer vape.
It achieves this in a number of ways all powered by the tiny PCB which is the heart of VIR. The technology behind VIR is all programmed into a unit the size of a thumbnail.
The VIR introduces a new paradigm in the vaping world, Imeo himself describes it as: "Real Greek Magic". An smart electronic module that understands your style of vaping.
Part of the Description is courtesy of GG160: http://gg160.blogspot.co.uk/
Features & Characteristics:
- 3 Years of research and development.
- Prevents inhalation of acrolein (produced when VG gets beyond 290°C).
- Can sense a non fed atomizer and prevents dry hits.
- Will not allow the wick to get dry, thus prolonging the life of the wick.
- Prevents wire from getting red hot: prevents oxidation.
- Checks the wick 1000 times per second, leading to consistent flavour.
- Parallel coils work with all the same functions.
- Control of vapor on atomizers with liquid control, especially on GG devices.
- Allows control of the vapor temperature.
- Through control and management of the current, VIR prolongs battery life.
- Performs the same regardless of the gauge of the wire used.
- Keeps vape consistent between atomizers with different resistances.
- Can sense overfed atomizer, and sends the correct power to remedy the flooded atomizer.
- Understands when you are not inhaling and cuts off after a few seconds.
- Gives a coloured LED signal depending on type of the detected wire.
- Detects available battery power and gives an LED signal when vaping falls below normal setup.
- Gives power when inhaling (if button is pressed without inhaling the power goes down): This provides protection for unlocked devices,as for example when carried in pockets.
- All changes work in real time, no need to stop and check settings.
- You know the temperature at which your atomizer works.
- Mechanical button
- No screen.
- "Working atomizer" check.
- "Strong / Weak" battery check.
- Lock mode.
- 15 Seconds cut off.
- Short circuit protection.
- Reverse battery protection.
- Over-discharge protection for battery.
- Thermal monitoring.
- Ability to stop LED flashes by pressing 1 time the button.
- Detect lower and higher limits of temperature range.
- Remembers your last set up.
- 0.45 - 2.2 Ohm resistance range.
- Atomizer won't work while pushing the button to enter the menu.
- Menu won't trigger by mistake, ie when using short button push inhales.
- Battery will work until it reaches 3,4 Volts.
- Width: 20,5 mm.
- Height: 15,5 mm.
- Weight: 10 grams.
- Brass electrical contact points (old alloy).
- Locking mechanism: "Electronic".
- Electro-mechanical button.
- Brass housing.
- Min-Max operating coil temperature: 180°C-280°C.
- Supported resistances: 0.45 ohms to 2.2 ohms.
- Supported coil materials: Titanium Grade 1.
- Power working range:
- Supported wire gauges: from 0.2 mm to 0.6 mm (from 32 AWG to 23 AWG).
- Locking / Unlocking: 5 button clicks.
- Over discharge battery protection: 3.3v.
- PCB temperature protection: 60°C.
Steps (configurable working temperatures):
|Increments of 20°C by step. From 180°C to 280°C.|
*Note: (with VIR unlocked) Two button clicks will show the current configured step or temperature, by a red blinking LED: Nine blinks = 180°C... ...fourteen blinks = 280°C.
Multi-Color LED Signal Meanings
- Fast blinking: Not enough liquid / not inhaling.
- Solid: Waiting for an already detected1 atomizer (for a max of 30 seconds2).
1 To change the atomizer remove the current atomizer and wait for 30 seconds until the green LED is off (VIR will forget the atomizer) and connect the new atomizer, the atomizer detection fase will start.
2 To have more than 30 seconds to work with an already detected atomizer, without losing its configuration (i.e. type of wire detected), you can lock the VIR by clicking the button 5 times before removing the atomizer or while in the 30 seconds range.
Tip: VIR will remember your latest configured step, even if a new atomizer is installed and wire detection process was executed.
- On for 1 second after 2 seconds of inhaling: Not enough battery power for the selected configuration (it will still functioning at the maximum power that the battery can supply. In other words, it will keep operating at lower temperature (step) than the selected, as there is not enough battery power to achieve the selected step)1.
- Slow blinking: Atomizer / Wire type detection process.
- Fast blinking: Short circuit detected.
1 It is important to note that it could happen even when the battery is fully charged and the selected step is the lower one. For example, in a situation of an overfed atomizer, in which the excess liquid will keep the coil at lower temperature than the configured at the selected step.
- Solid (1 second): Locked device (after clicking 5 times the button).
- 3 Blinks: Unlocked device (after clicking 3 times the button).
Tip: You can stop any LED signal at any time by clicking one time the button.
Atomizer coil / wire type detection (after detection fase):
- Orange: (solid, one second) Titanium grade 1 or e-smokeguru titanium alloy wire detected.
- Light Blue: (solid, one second) Stainles Steel wire detected.
- Purple: (solid, one second) Other coil materials detected (as Kanthal, Nichrome, etc).
Instructional Videos & Reviews
- Temperature regulation in e-cigarettes: first measurements presented by Dr. Konstantinos Farsalinos
- Vapers Time S2E2. Starring Imeo, Vassilis, Fotis, Ellines & Dr. Konstantinos Farsalinos (Greek) - by Ellines Atmistes: http://vaperstime.com/
Tips & Trick’s
More VIR Pictures